Home - Return to Previous Page

Ford 6.0L Powerstroke ICP Sensor & Connector Kit (2003-Early 2004)

ICPK-6.0-0304

ICP Sensor and Connector Kit

Fits 2003-2004 Ford 6.0L Powerstroke Diesel with ICP sensor located in rear of engine on the injection pump

Availability: CA: 76
Was: $99.95
Sale: $79.95
Save: 20%
Save: $20.00

Qty:
Free Ground Shipping

Description

This NorCal Diesel Performance kit replaces the Injection Control Pressure (ICP) sensor and the electrical connector pigtail on 2003–early 2004 Ford 6.0L Powerstroke engines that still use the early sensor location: the rear high-pressure oil pump (HPOP) cover, under the turbo and up-pipes.

On these early engines the sensor sits in a high-heat area next to the turbo and up-pipe collector. The ICP sensor measures high-pressure oil in the HEUI injection system, and the engine computer uses that reading to control the injector pressure regulator (IPR) valve. Heat, plus oil leaking through a failed sensor into the connector, commonly soaks the pigtail, corrodes the terminals, and causes erratic ICP readings. That is why the connector is replaced with the sensor.

Typical symptoms of a failed ICP sensor or oil-soaked pigtail include hard starting or a long crank, no-start, rough idle or stutter, stalling, and abnormal ICP readings. Related diagnostic trouble codes can include P2284, P2285, P2287, and P2291. A code or a low ICP reading alone does not prove the sensor is at fault; a weak HPOP, an IPR problem, or a high-pressure oil leak can set the same codes. A common field check is to unplug the ICP sensor: if the engine then starts and runs more normally, the sensor or its pigtail is a likely cause.

What's in the kit

  • OEM Quality ICP sensor 
  • 3-wire connector ICP pigtail
  • Three crimp (butt) connectors

This is a NorCal Diesel Performance house-brand kit (SKU ICPK-6.0-0304). It is a direct-fit replacement for the early-style sensor and connector, not a genuine Ford/Motorcraft part.

This kit is backed by a 2-year warranty from NorCal Diesel Performance. If there's an issue, contact us.

Fitment — confirm the sensor location first

This kit fits 2003 and early 2004 Ford 6.0L Powerstroke engines in the F-250, F-350, F-450, and F-550 Super Duty and the Excursion, and only when the ICP sensor is on the rear HPOP cover under the turbo. It does not fit late 2004–2010 6.0L engines with the sensor in the passenger-side valve cover, and it does not fit 7.3L Powerstroke engines.

  • Look first: if the ICP sensor is on the rear HPOP cover under the turbo and up-pipes, this is the correct kit. If it is on the passenger-side valve cover, use the 2004.5–2010 ICP sensor and connector kit instead.
  • 2003 Super Duty and Excursion: these model years were sold with either the 6.0L or the 7.3L. This kit is 6.0L only. For a 1994–2003 7.3L, use the 7.3L ICP sensor and connector kit.
  • 2004 model year: early 2004 trucks were still built with the 2003-style engine and the rear ICP sensor. Later 2004 (“2004.5”) trucks moved the sensor to the valve cover. Do not order by model year alone.
  • Build date: the early-style engine was used on engines built before September 29, 2003. The vehicle build date is on the white sticker in the driver's door jamb. If the truck was built on or near that date, check the engine serial number or the sensor location to confirm.
  • Engine serial number: Indianapolis-built engines through serial number 6,155,636 use the early, rear-mounted ICP sensor. Late-style engines begin at serial number 6,155,637. Huntsville-built engines use the early sensor through serial number 94,580 (0094580). If you are unsure, check your engine serial number or the sensor location to confirm.

OEM cross-references (sensor)

This kit is a replacement for the early, rear-mounted ICP sensor. Ford's current part number is 3C3Z-9F838-A, which supersedes 3C3Z-9F838-AA, 3C3Z-9F838-DA, and 3C3Z-9F838-EA. Navistar/International numbers are 1845274C91 and 1845274C92.

The Ford pigtail commonly specified for this connector is 5C3Z-12224-A.

This kit is a quality aftermarket sensor and pigtail.

Installation notes

On early 6.0L engines the sensor is tight to reach, behind the turbo and under the up-pipe collector, next to the IPR valve. Inspect the connector for oil and heat damage, and replace the pigtail whenever the sensor is replaced if the connector is soaked, brittle, or corroded. Follow a 6.0L service procedure for access, o-ring lubrication, and torque. 

Questions about which kit you need? Call 888-290-3820 and we can help you confirm the sensor location before you order.

Shipping Information

  • Item Requires Shipping
  • 1.0 lbs.
  • W4.0000” x H2.0000” x L6.0000”
  • Free Ground Shipping

Customer Reviews

Comment Total Reviews (0)

Write the First Review!

You must login to post a review.